Lighting Range
Lamp Controllers
★ ★ ★ ★ ★
Customer Reviews
Just purchased T5 Plant Pro and my plants love it, good product.
Ohayo Mosi
Related Products
Ultra Seal T8 Controllers
Easily adds additional T8 lighting to an aquarium.
Ultra Seal Electronic Controller
A new electronic fluorescent lighting controller range from Arcadia, featuring high frequency electronic ballast.
Fluorescent Lamp Reflector
Double your light output with our reflector. It ensures stray light is redirected into the aquarium, maximising efficiency.
PLANT PRO LAMP – T5 / COMPACT
The T5 Plant Pro lamp has been specifically formulated to combine the red and blue spectral peaks of the Original Tropical Lamp to support plant photosynthesis, with the higher light output of the freshwater lamp.
The result is a lamp which is noticeably brighter than the Original Tropical, making it ideal for more demanding plant species.
- Ideal for growing more demanding aquatic plants
- Bright penetrating light, ideal for even deeper aquariums
- Enhance colours of fish and plant
- Satisfy plant species with a higher light requirement
| Code | Watt | Length | Diameter | Lumens | CRI | Reflector* |
|---|---|---|---|---|---|---|
| FPP24T5 | 24W | 22″/550mm | T5-16mm | 1050lm | 1B | ALRS24 |
| FPP39T5 | 39W | 34″/850mm | T5-16mm | 1950lm | 1B | ALRS39 |
| FPP54T5 | 54W | 46″/1150mm | T5-16mm | 2800lm | 1B | ALRS54 |
| FPP80T5 | 80W | 58″/1450mm | T5-16mm | 3700lm | 1B | ALRS80 |
J5 Plant Pro Lamps
Also available in Juwel® aquarium lengths:
| Code | Watt | Length | Diameter | Lumens | CRI |
|---|---|---|---|---|---|
| FPPJ24S | 24W | 18″/438mm | T5-16mm | 1100lm | 1B |
| FPPJ28 | 28W | 24″/590mm | T5-16mm | 1600lm | 1B |
| FPPJ35 | 35W | 30″/742mm | T5-16mm | 1900lm | 1B |
| FPPJ45 | 45W | 36″/895mm | T5-16mm | 2300lm | 1B |
| FPPJ54S | 54W | 42″/1047mm | T5-16mm | 2750lm | 1B |
| FPPJ54L | 54W | 48″/1200mm | T5-16mm | 2800lm | 1B |
| Code | Watt | Length | CRI | Cap |
|---|---|---|---|---|
| FFPC18 | 18W | 8.5″/215mm | 1B | 2G11 |
| FFPC24 | 24W | 13″/320mm | 1B | 2G11 |
| Code | Watt | Length | CRI | Cap |
|---|---|---|---|---|
| FFPC18E | 18W | 8.5″/215mm | 1B | 2G11 |
| FFPC24E | 24W | 13″/320mm | 1B | 2G11 |
Product Safety
Lamps can be fragile pieces of equipment. Please follow the following steps to ensure the safe fitting and use of fluorescent lamps.
At either end of a fluorescent lamp you will see two brass coloured connection pins. These are the electrodes that take energy from the controller to start and run the lamp. These are quite fragile by nature. It is imperative that both pins are safely located into the pin sockets inside the lamp holder before the lamp is pressed into place. Failure to line the pins up correctly will cause the pins to bend and snap and break through the lamp cap rendering the lamp unusable.
The Ultra-seal lamp ring must be unscrewed from the lamp holder and placed over the lamp prior to fitting and only re-seated onto the lamp holder when you are sure that the lamp pins are seated correctly. High Output T5 lamp leads must be fully unwound also or you may notice lamp flickering or beaks in illumination. You can also use a very small amount of a substance like Vaseline to lubricate the lamp ring and so stop it fusing to the lamp after long periods of heat. After cooling lamps can be wiped clean with a damp cloth once every two weeks or so to remove any dust build up from the lamp, this in turn will help to maintain the lamps full output. The all important reflector should also be wiped clean at the same time.
Lamp Reminder Service…
Is your lamp still emitting the correct amount of UV!
The amount of light emitted from a lamp decreases with the age of the lamp, particularly in lamps which emit ultraviolet radiation, so it is important to remember to change you lamps at the end of their recommended service life.
