LED T5 Tubes

/, LED, Marine, T5, Tropical/LED T5 Tubes

LED T5 Tubes

Traditional T5 end caps for direct replacement of Fluorescent Lamps. Uses 1/3 electricity, producing  double the light of equivalent fluorescent.

Add the ripple effect. Even with T5 fluorescent lamps, will make a difference. Lampholder rotates to direct light correctly. Waterproof when used in conjunction with the IP67 ULTRA SEAL® lampholders.

Categories: , , , ,

Description

Code Watt Length Diameter Energy kWh/1000h
FFEET24 8W 12″/300mm T5-16mm A+ 8
FFEET39 14W 15″/360mm T5-16mm A+ 12
FFEET54 15W 18″/450mm T5-16mm A+ 18

 

Compatible with Juwel® aquariums

Code Watt Length Diameter Energy kWh/1000h
FFEETJ24S 8W 17″/438mm T5-16mm A+ 8
FFEETJ28 8W 23″/590mm T5-16mm A+ 8
FFEETJ35 12W 29″/742mm T5-16mm A+ 12
FFEETJ45 12W 35″/895mm T5-16mm A+ 12
FFEETJ54S 18W 41″/1047mm T5-16mm A+ 18
FFEETJ54L 18W 48″/1200mm T5-16mm A+ 18

Code Watt Length Diameter Energy kWh/1000h
FFEEF24 8W 12″/300mm T5-16mm A+ 8
FFEEF39 14W 15″/360mm T5-16mm A+ 12
FFEEF54 15W 18″/450mm T5-16mm A+ 18

 

Compatible with Juwel® aquariums

Code Watt Length Diameter Energy kWh/1000h
FFEEFJ24S 8W 17″/438mm T5-16mm A+ 8
FFEEFJ28 8W 23″/590mm T5-16mm A+ 8
FFEEFJ35 12W 29″/742mm T5-16mm A+ 12
FFEEFJ45 12W 35″/895mm T5-16mm A+ 12
FFEEFJ54S 18W 41″/1047mm T5-16mm A+ 18
FFEEFJ54L 18W 48″/1200mm T5-16mm A+ 18

Code Watt Length Diameter Energy kWh/1000h
FFEEW24 8W 12″/300mm T5-16mm A+ 8
FFEEW39 14W 15″/360mm T5-16mm A+ 12
FFEEW54 15W 18″/450mm T5-16mm A+ 18

 

Compatible with Juwel® aquariums

Code Watt Length Diameter Energy kWh/1000h
FFEEWJ24S 8W 17″/438mm T5-16mm A+ 8
FFEEWJ28 8W 23″/590mm T5-16mm A+ 8
FFEEWJ35 12W 29″/742mm T5-16mm A+ 12
FFEEWJ45 12W 35″/895mm T5-16mm A+ 12
FFEEWJ54S 18W 41″/1047mm T5-16mm A+ 18
FFEEWJ54L 18W 48″/1200mm T5-16mm A+ 18

Code Watt Length Diameter Energy kWh/1000h
FFEEB24 8W 12″/300mm T5-16mm A+ 8
FFEEB39 14W 15″/360mm T5-16mm A+ 12
FFEEB54 15W 18″/450mm T5-16mm A+ 18

 

Compatible with Juwel® aquariums

Code Watt Length Diameter Energy kWh/1000h
FFEEBJ24S 8W 17″/438mm T5-16mm A+ 8
FFEEBJ28 8W 23″/590mm T5-16mm A+ 8
FFEEBJ35 12W 29″/742mm T5-16mm A+ 12
FFEEBJ45 12W 35″/895mm T5-16mm A+ 12
FFEEBJ54S 18W 41″/1047mm T5-16mm A+ 18
FFEEBJ54L 18W 48″/1200mm T5-16mm A+ 18

Product Safety

Lamps can be fragile pieces of equipment. Please follow the following steps to ensure the safe fitting and use of fluorescent lamps.

At either end of a fluorescent lamp you will see two brass coloured connection pins. These are the electrodes that take energy from the controller to start and run the lamp. These are quite fragile by nature. It is imperative that both pins are safely located into the pin sockets inside the lamp holder before the lamp is pressed into place. Failure to line the pins up correctly will cause the pins to bend and snap and break through the lamp cap rendering the lamp unusable.

The Ultra-seal lamp ring must be unscrewed from the lamp holder and placed over the lamp prior to fitting and only re-seated onto the lamp holder when you are sure that the lamp pins are seated correctly. High Output T5 lamp leads must be fully unwound also or you may notice lamp flickering or beaks in illumination. You can also use a very small amount of a substance like Vaseline to lubricate the lamp ring and so stop it fusing to the lamp after long periods of heat. After cooling lamps can be wiped clean with a damp cloth once every two weeks or so to remove any dust build up from the lamp, this in turn will help to maintain the lamps full output. The all important reflector should also be wiped clean at the same time.

Reviews

There are no reviews yet.

Be the first to review “LED T5 Tubes”

Your email address will not be published. Required fields are marked *

You may also like…